Why is My SSD Not Showing All Files? Easy Guide

Solid drives (SSD) are faster, thinner, newer and the little brother of hard drives. These storage units make navigation faster and easier for people. But why is my SSD not showing all files in Windows Explorer or Disk Management? Nothing on the drive may be accessible.

Windows not recognizing an SSD or a new SSD is a common and difficult problem. I hope you can fully understand the reasons why SSDs are not showing up in this article and get a comprehensive solution to fix SSDs not showing up in Windows.

But if SSD data is inevitably lost during the recovery process, you can use data recovery software to quickly recover the lost files.

Common Causes of  SSD Not Showing All Files

Solid-state drives are not as susceptible to mechanical failure or sudden shock as hard drives, but they can be damaged due to electronic errors or physical damage. Below are the most common reasons why an SSD shows up:. 

• You installed a new SSD, but it has not yet been initialized.
• The system cannot recognize the partition.
• I don’t see the drive letter after the partition
• The section is hidden.
• SSD not detected by Windows operating system
• You may have a problem with your driver software.

Why is My SSD Not Showing All Files? Most-Tested Software by Expert

You can use a dedicated PCVITA SSD Disk Recovery Tool, such as Data Recovery Free. With this DIY software, you can recover files and folders from Windows systems and media storage devices such as HDD, SSD, USB flash drives, SD cards, etc.

It provides a format scan option to display all formatted files in the software information panel. This way, users can easily select data files and save them to the desired folder. This tool allows users to easily recover data from a solid state drive. It works for all data loss scenarios , for example.

Follow these steps:

• Download and launch the free SSD data recovery program and select the device you want to recover.

• View basic information about your device and select a scan type.

• Select a folder to view all recovered data.

• Save important files to a location of your choosing.

Why is My SSD Not Being Detected? Manual Techniques

There are several manual solutions that will help you fix this annoying error. Explain this method descriptively. So, users can easily monitor and run it to solve the undetected SSD problem.

Solution 2: Reconnect the SATA cable to fix the “SSD Not Recognized” Error

First, disconnect the SATA data cable from the SSD and leave the power cable connected.

1. Now turn on your computer and boot into the BIOS.
2. Let the system run in the BIOS for about an hour, and then turn off the computer.
3. Here, connect the SATA cable to the SSD again and turn on the computer to boot into BIOS.
4. You need to make sure the boot sequence is correct, save and boot Windows.

Finally, you can now check and read everything on your SSD drive. If that doesn’t work, move on to the next one.

Solution 3: Update your Driver to Fix the SSD Not Being Detected Error

1. First, click the Start button, type Device Manager and press Enter to open it.
2. Then expand the Drive Drivers category, right-click each driver, and select Update Driver.
3. Finally, after the process is completed, restart your computer.
4. You can then check and view the data stored on your computer’s SSD.

Solution 4: Run a CMD Command to fix the “SSD Not Found” Issue

If your computer is warning you that your SSD’s file system is corrupted or your SSD has stopped responding due to an unknown file system error, the CMD command can easily fix these errors.

• Open a command prompt and type “chkdsk /f c” (replace c with the drive behind the external hard drive).
• Now press “Enter” to run the test.
• After that, type “exit” and press “Enter” to complete the process.
• You will then be able to access and read data from your computer’s SSD.

Solution 5: Update the Firmware for the SSD Issue

• As a first step, right-click the Start icon and select Device Manager from the left pane.
• Then expand Disk Drives, right-click the SSD drive, and select Properties.
• Now select “Hardware ID and Information” in “Properties” and click “OK.”.
• Here, install and run “SSD Firmware Update Tool” to check the SSD firmware version using this tool.
• Select “Permissions” and click “OK.”
• Then select Available Updates, click Update Disk, and select Yes to confirm the update.
• In the last step, click “OK” to complete the firmware update process. After this, you can close the updater and check your SSD immediately.

Closing Line of this Blog

Why is my SSD not showing all files? A new SSD is a common and difficult problem. I hope you can fully understand the reasons for not recognizing an SSD in this article and get a comprehensive solution on how to fix SSD Not Being Detected in Windows.

However, if the data saved on the SSD is inevitably lost during the recovery process, you can use data recovery software to quickly recover your lost files.